![how to make a homemade pipe tamper how to make a homemade pipe tamper](http://i.ytimg.com/vi/wfQQXaQH8Z8/maxresdefault.jpg)
Then add the second layer and repeat the process until the entire base if at a compacted depth of four inches. Spread the first layer with a rake and compact it down to a depth of two inches with either a tamper or a plate compacter.
![how to make a homemade pipe tamper how to make a homemade pipe tamper](https://i.etsystatic.com/8236970/r/il/ae833c/1923626266/il_794xN.1923626266_n9el.jpg)
Pour the gravel or another aggregate into the excavation area in two increments. Periodically check the depth of your base as you dig it to make sure it slopes correctly, otherwise you will have drainage issues that could compromise the structure of your paver patio. The base area should slope about 1/4 inch for every foot of distance. Lubricate the stuffing horn with olive oil, and slide as much of the casing up on it as you can. This is definetely a two person job, especially if you are using the hand-cranked grinder. Measure from the edge closest to your home, to the opposite edge of your planned patio. Use the meat grinder and stuffing tube to fill the sausage casings.
![how to make a homemade pipe tamper how to make a homemade pipe tamper](https://m.media-amazon.com/images/I/71b-r6922pL._AC_SL1500_.jpg)
It is better to dig up a little deeper, as this depth can be filled later using the aggregate if you need to.Īlso, you will need to adjust your depth based on the width of your patio. Excavate the area, making it deep enough to hold the pavers, about one inch of sand, and three to four inches of aggregate. With the area roped off and set, you can start digging up the grass using a shovel. Use a line level to place a string between the stakes to form an outline for your excavation area. Measure the area for your patio in the location you decided on and move out about six inches on all sides before putting your wooden stakes in the ground. Once the initial planning is complete, ensure you have all the materials required before starting work on the project. Use a pencil and keep an eraser handy when doing the drawing as you may have to make changes as you go.
How to make a homemade pipe tamper windows#
Also, make sure you consider the sightlines from any nearby windows and avoid placing it near any underground utilities. Map out the existing landscape of your yard, noting any existing trees, walkways, or other permanent fixtures before you sketch out where you want to put the patio. With the bucket level tool, allow time for it to come to the temperature of the water already in the bucket if further water is added.The need for a good plan cannot be ignored when working on a patio, particularly since there are a lot of aspects to think about before breaking ground. It’s very important that you make sure there are no air bubbles in the level tool to have proper accuracy. All you need to do is mark where the level is to carry out the work. The water level in the tube will look a little concave but that’s perfectly normal. Hold the tube against the vertical surface and give the water a moment to settle. Rest the bucket on a surface close to the vertical surface that you want to level. Because of the length of this tube, it’s best used by two people working together. The water at the other end will be at the same level so you can mark it accordingly and make any adjustments if they necessary. To use the level, hold it so that the waterline on one end is at the mark you need to read. The waterline in the tubing of the level tool will be a little lower than the top of the tubing. Now, unclamp the tube and allow water to flow through into the sink until you see no more air bubbles before clamping again. Fill the bucket with water that’s been colored by food coloring. Apply a clamp over the end and stand the bucket on the kitchen counter with the tubing trailing into the sink. There should be a long length of tubing outside the end of the bucket. Caulk around the hole in the bucket, both inside and out, to make it waterproof and allow it to dry. Pull several inches of the tube through until it reaches close to the center of the bucket. The hole needs to be slightly smaller that the outside dimension of the surgical tube. Drill a hole in the side of the bucket down near the bottom. There’s more involved in making a bucket level tool but not a great deal more. Fold over and clamp the other end after making sure that there are no air bubbles in the tube. Mix water with some food coloring and pour into the tube, leaving about 2 inches of air at the top. To make a tube level tool, all you need to do is fold over and clamp one end of the surgical tubing to ensure it won’t leak.